G'day,
Can do it, but this is hardly the day sailing trailer sailer, the
cabin will ned to be high at the ends so you can sit up in the bunks,
and where do you sit to sail the boat?
regards,
Rob
On Thu, May 29, 2008 at 1:34 AM, Gardner Pomper <gardner@networknow.
> Pursuing the idea of making the ww hull a bit longer, I have uploaded
> another sketch to the file "trailerable Pomper". I am deliberately trying to
> leave as much of the interior of the hull unfinished as I can, and
> (naturally), I need to have standard size bunks. The pop top can have roll
> down clears for foul weather. The bunks are covered with clear lexan, which
> can be flipped up to enclose the cockpit when the weather is bad, or you
> want to use them. You enter the bunks from the flip down walkway, or over
> the back of the lazarrette.
>
> I don't know that I added much weight, so hopefully we can preserve the 10:1
> ratio on the ww hull.
>
> - Gardner
>
> On Wed, May 28, 2008 at 1:19 AM, Rob Denney <harryproa@gmail.
>>
>> G'day,
>>
>> Preliminary numbers
>>
>> ww hull 5m/15' long, waterline 450mm/18", draft 220mm/8.5",
>> displacement 640 lbs, prismatic .77. (Use this to allow for the hull
>> shape when you multiply the cross sectional area in the middle of the
>> boat by the length). I would probably go a little longer to cope
>> with your other requirements.
>> lw hull, as long as you can build, trail, afford and handle. The
>> longer it is, the higher the top speed and the drier and more
>> comfortable the motion.
>>
>> The single sail works well on boats with light windward hulls, as the
>> rudder is aft, which makes it balanced. With 600 kgs on a shortish ww
>> hull, the ballestron may be a better bet, although once you know how
>> to shunt, it won't be a problem. With a lot of people on board, and
>> not much boom clearance the ballestron needs to be watched while
>> shunting.
>>
>> There will be trampolines, which will be on side pieces with a hinge
>> in the middle so it can be folded when the boat telescopes. A
>> walkway can do the same.
>>
>> Sail is loose footed (attached only to the outboard end of the boom).
>> On Elementarry, the boom is attached to the mast. It has a sock luff,
>> so this is not a problem. Yours would have slides, so the boom needs
>> to rotate relative to the mast, but not move vertically. Not a big
>> deal. Your boom will indeed be too long to attach permanently. It
>> will be strapped to the bearing on the mast, again, not a big deal.
>>
>> The hours on the charter boat are for the shell. This one could take
>> anywhere from 500-1,000+ hours depending on all the usual stuff, but
>> mostly on the standard of finish required. There are some alignment
>> details to make it telescope smoothly, which could add some time.
>> They are all done before the beams are closed up permanently, so are
>> not difficult, just might take a while.
>>
>> Materials cost? Same as the other trailer sailor, give or take a bit.
>> It is cheaper to import the materials from here. Let me or Raps
>> know if you want to share the shipping costs.
>>
>> Could be a single bunk, or the galley and stowage. The double is
>> 6'x5', the single is 5x3. Yours will have the cockpit in this area.
>> The toilet at one end of the hull and the galley at the other end.
>> Access will be through deck hatches.
>>
>> Re infusion. Derek's workshops are fantastic, Henny at
>> http://www.fram.
>> Houston, but I don't have his web address. By far the best way to
>> learn about it is:
>>
>> Get a vacuum pump from ebay, (old milking pumps, fridge compressors,
>> air con evacuators all work) and a sheet of window glass about 30"
>> square. Buy some clear builders plastic, some window sealant, glass,
>> foam, peel ply and resin, some shade cloth and some 10mm plastic
>> conduit. Drill the smallest holes you can every 4" in the foam and a
>> 1/4" hole every 4" in the middle 18" of 2 pieces of 4' lengths of
>> conduit, cut the cloth and peel ply and lay it on the glass with a 2"
>> border all the way round. Put the shade cloth on the glass and wrap
>> it around the perforated section of the lengths of conduit such that
>> one piece is on one side of the job, the other is on the opposite
>> side. Cut a piece of plastic the same size as the glass and seal it
>> to the glass and around the conduit. Block one end of one piece of
>> conduit and hook the other end up to the vac pump. Block both ends
>> of the other piece. Check for leaks (listening) is the best way.
>> When it is leak free, unseal the ends of the non vacuum conduit and
>> put them in buckets of resin. Prepare to be amazed. When the
>> infusion is complete (look under the glass aswell as on top), seal off
>> the resin conduit and leave it to cure. You now know more about
>> infusion than 95% of the world's boatbuilders. Study and weigh the
>> sample, and let me know what it looks like and what went wrong and I
>> will start lesson 2.
>>
>> Elementarry as a tender? Could do, but without seats, it is not very
>> comfortable. It is also a bit fragile for hauling up beaches and over
>> rocks. The Torqueedo would work, but rowing wouldn't. No sweat on
>> the payload, but it would all be on the trampoline. You would be
>> better off with a conventional dinghy. Loading El on the cabin top
>> for blasting around when you get there has more merit, but the mother
>> ship really should be bigger for this.
>>
>> Let me know what the next step is, or if I have forgotten to reply to
>> anything.
>>
>> regards,
>> Rob
>>
>> On Tue, May 27, 2008 at 11:57 PM, Gardner Pomper <gardner@networknow.
>> wrote:
>> > Hi,
>> >
>> > Ok, I can tell by the responses that it won't be a small boat :( I was
>> > hoping for something smaller than the design that is taking shape. Since
>> > that looks to be not true, let me fall back to that one, and drop the
>> > weight
>> > requirements and the 6 passenger (we will only invite people on a nice
>> > day
>> > for a few hours. They can sit on the trampolines (there can be
>> > trampolines,
>> > right?) Then we can design for crew weight of 600lbs, and seating for
>> > 3-4.
>> >
>> > I notice that you are not using the ballestron right. I am flouting my
>> > ingorance here, but how can you go upwind with a mast centered for and
>> > aft
>> > and no headsail?
>> >
>> > I was also thinking of a 3-4' flat panel, hinged at the floor, to give
>> > some
>> > sort of walkway outside the cockpit. Fold it down once the beam is
>> > expanded.
>> >
>> > Is the sail loose footed? The charter proa talks about the boom and mast
>> > being one piece, but it would seem to make it too wide for trailering.
>> >
>> > Since you have basics worked out on that trailer sailor, do you have an
>> > estimate of work hours for an "average" finish? I know you have
>> > mentioned
>> > 1400 for the charter proa hull (by professionals, I am sure).
>> >
>> > There looks to be a single bunk "forward" also. Is that true, or is that
>> > the
>> > galley? What are the bunk dimensions?
>> >
>> >
>> >
>> > On Tue, May 27, 2008 at 11:38 AM, Rob Denney <harryproa@gmail.
>> > wrote:
>> >>
>> >> G'day,
>> >>
>> >> On Tue, May 27, 2008 at 11:00 PM, gardnerpomper
>> >> <gardner@networknow.
>> >> wrote:
>> >> > Hi,
>> >> >
>> >> > Some sort of liveaboard harryproa seems like my next cruising boat. I
>> >> > am interested in both sampling the experience, and finding out if I
>> >> > have the fortitude to build one. I have seen messages about a
>> >> > trailerable design and I have some questions specific to using it to
>> >> > "try out" the home build/proa idea.
>> >> >
>> >> > Requirements:
>> >> > 1) trailerable as other specs (8'6" trailer width,
>> >> easy
>> >> ><1000lbs with trailer (negotiable)
>> >> Difficult, negotiations can start when i have done some drawings.
>> >> > 2) build method as similar to proposed charter boat as possible,
>> >> > since
>> >> > that is identified as simplest for larger boats
>> >> > fast and easy on/off the trailer. this would be a daysailer, driving
>> >> > 2
>> >> > hours to the water, set it up, sail for a few hours, break it down,
>> >> > trailer it 2 hours home.
>> >> Easy
>> >> > 3) I am heavy (300lbs), so the crew weight (3 of us) would be about
>> >> > 550lbs. We would like to be able to invite another 2 adults and a
>> >> > child and still sail it well, so total crew weight could be 900 lbs.
>> >> Difficult, I will see what the minimum size is to do this. How much
>> >> extra for food and safety gear?
>> >> > 4) Enclosed head
>> >> easy
>> >> > 5) sail without getting wet
>> >> easy
>> >> > 6) camping propane stove
>> >> > 7) comfy seats and table to eat at
>> >> Can this be outside, under a removable bimini with roll down sides?
>> >> Otherwise, it is a bit ticky for 6 people.
>> >> > 8) standing headroom (fold down bimini ok)
>> >> easy
>> >> > 9) rain protected
>> >> easy
>> >> > 10) will never be INTENTIONALLY sailed in > 20 kts
>> >> Yeah, right!
>> >> > 11) ballestron rig
>> >> easy
>> >> >
>> >> > I won't be racing, but I will want performance comparable to what we
>> >> > have heard from Rare Bird and the charter proa design (i.e. windspeed
>> >> > up to 15 knots). I *don't* want to fly a hull!! (I'm timid)
>> >> Timid is good, but it will be a sizableboat to do this with 6 people on
>> >> board.
>> >> >
>> >> > Questions:
>> >> > 1) What would plan cost be?
>> >> TBA when i see what is involved. Probably $Aus3,000, as it is going
>> >> to be a one off. You get 10% off any future plans sold to the
>> >> design until the next one is sailing. After that it is as per the
>> >> Goodwill Fee on http://www.harrypro
>> >> price wil be deducted from the big boat fee.
>> >> 2) would plans include info on resin infusion and building a table,
>> >> > etc, etc? Or at least point me to such info?
>> >> yes. As much information as you need on anything in the plans.
>> >> > 2) Estimated build time (novice.. experienced with epoxy/fiberglass,
>> >> > even some with carbon mat as reinforement, but never built a boat).
>> >> > If
>> >> > you prefer, you can supply "average estimated build" and I will put
>> >> > in
>> >> > my own "idiot factor" multiplier
>> >> TBA, but mostly it will depend on the level of finish inside and
>> >> outside that you require.
>> >> > 3) Would it be close to the "trailer sailer" layout jpg I see posted
>> >> > in the forums?
>> >> Not if you want a cockpit for 6, which will replace the bunks
>> >> >What are hull lengths?
>> >> Long! What is the longest you can build, trailer and handle on the
>> >> ramp?
>> >> > 4) When could I start? I have a building available this summer/fall,
>> >> > but it is not heated
>> >> Tomorrow, building the table. You won't get all the plans
>> >> immediately, but i will keep ahead of your progress. Pay for half the
>> >> plans up front, the rest before the last drawings arrive.
>> >> > 5) material cost? availablity?
>> >> Not a huge amount, probably less than the resale value of the boat.
>> >> Can get it from your local supplier, apart from the carbon for the
>> >> mast, boom, rudders and beams which I will supply from Texas.
>> >> >
>> >> > BTW, I live in Pennsylvania (US).
>> >> No problem ;-)
>> >>
>> >> > Thanks,
>> >> > - Gardner
>> >>
>> >> My pleasure,
>> >>
>> >> Rob
>> >> >
>> >> >
>> >
>> >
>
>
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch format to Traditional
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe